Week 13

Date:23/10/2019 (Wednesday)

Title:  Presentation of Final Year Project

The Final Year Project presentation was conducted at Dewan Gemilang British Malaysian Institute at 8am to 12pm which is our.assessor was Dr. Mohd Zain @ Mohd Fauzi Bin Ismail and Mohamed Razif Bin Mohd Noordin.

After we done the presentation,we were thankful because everything is going well for the presentation. After the presentation,it is time to prepare the report.

ACKNOWLEDGEMENT: 

First of all, we would like to thank my supervisor Madam Punitha for her guidance, advice and attention throughout the development of this project. This project would not have happened without the supports of our family. We would like to thank our beloved parents and siblings who have help to encourage whenever we feeling down.

We would also like to thank all of our friends for the supports. Our friends have helped we a lot in improving our knowledge and skills. Then, we would like to thank all the lecturers that have taught me throughout my studies. We will try to use the knowledge that have been taught as good as we can. Lastly we would like to thank those who have helped we in developing this project.

Week 12

Date:14/10/2019 - 18/10/2019
Title: Preparation for the presentation FYP day.


In this week, we do many things for the project which is troubleshoot, construction the model and prepare the poster for presentation.


Equipment and tools that we used to complete this model:
    1) Pt Board
    2) Hot glue
    3) Plywood
    4) Board
    5) Double Tape
    6) Ruler
    7) Scissor
    8) Colour Paper
    9) Tack tape 
   12) Driller
   13) Cutter

The poster needs to have :

• Project title 
• Student's name
• Logo University
• Block diagram
• Flow Chart
• Objectives
• Methodology
• Conclusion
• References 

And the last day before the FYP exhibition day, we meet our supervisor Madam Punitha to test and demo our project to get her opinion for the exhibition day.

Week 11

Date:7/10/2019
Title: Combine the project


In this week, we have to Combine the project which is Arduino Uno is the main component as a connector to this two project. All the hardware for this project were combined according to the circuit schematic above.

After the process of combination is done, my partner made a block diagram while I made a flowchart for our banner to be prepared for our exhibition day. This is our flowchart and block diagram.

Week 10

Title: Final FYP Diploma Briefing 

This week is about the final briefing of the Final Year Project.

Date: 2nd October 2019 (Wednesday)

Venue: TTL2

Time: 3 pm to 5pm

  

In the final briefing, the FYP committees have explained us about :

·         FYP Diploma Exhibition Day (Tips & Tricks)

          Submission of Progress Report & Final Report

In conclusion, the contents for this week were clearly understood by students. This can help student to be well prepared for FYP Exhibition Day and also in doing a complete Thesis.

Week 9

Date:23/9/2019 -27/9/2019
Title: Making a connections

In this week, I make a connection and put a program code into arduino to command the LCD using arduino software. There are many trials that i made for installing a code into arduino because it is my first time using arduino.




The circuit that i marked in red was my project. This voltage sensors can read the value in the voltage. Why i used two sensors? Because first is to measure the value of voltage in the circuit and the others is to measure the value of voltage of the solar recieved. After that, I write a coding and install into Arduino.



Other than that, my project is to connect the solar panel to the battery to be charges.

Week 8

Date: 9/9/2019 (Monday)
Title : Research and findings

In this week I’m continuing my research about LCD (Liquid Crystal Display). In my project, I would like to interface arduino with LCD. 

Introduction of LCD

 LCD (Liquid Crystal Display) screen is an electronic display module and find a wide range of applications. A 16x2 LCD display is very basic module and is very commonly used in various devices and circuits. These modules are preferred over seven segments and other multi segment LEDs. The reasons being: LCDs are economical; easily programmable; have no limitation of displaying special & even custom characters (unlike in seven segments), animations and so on.

A 16x2 LCD means it can display 16 characters per line and there are 2 such lines. In this LCD each character is displayed in 5x7 pixel matrix. This LCD has two registers, namely, Command and Data.

This is a datasheet of LCD 16x2

From datasheet above, LCD 16x2 can using 16 pin(for 8 bit) and 12 pin(for 4 bit). I try to connected  the lcd to my arduino.

Arduino LCD 16x2 Display  interface (4 bit)

Week 7

Title: FINAL YEAR PROJECT Workshop

This week is about the Workshop of the Final Year Project.

Date: 4th September 2019 (Wednesday)

Venue: TTL2

Time: 3 pm to 5pm

  

In the workshop, the FYP committees have explained us about :

·         Result and Discussion (Chapter 4)

          Conclusion (Chapter 5)

          Abstract Writing

In conclusion, the contents for this week were clearly understood by students. This can help student to be well prepared in doing a complete Thesis.